Updated May 2026 · Local pricing for the Salt Lake City metro area
Free quotes from pre-screened local contractors. No signup required.
Powered by Thumbtack
Prices estimated using the NailThePrice Local Cost Model™ — national averages adjusted for Salt Lake City's labor rates, cost of living, and material pricing.
The cost to install a furnace in Salt Lake City ranges from $2,550 to $8,170, with most homeowners paying around $4,590. Your actual cost depends on several factors specific to your home and the Salt Lake City market.
Gas furnaces are most common and cost-effective in areas with natural gas. Electric furnaces cost less to install but more to operate. Oil furnaces need a storage tank.
Standard-efficiency (80% AFUE) furnaces cost less upfront but waste 20% of fuel. High-efficiency (95–98% AFUE) units cost more but save $200–$500 annually on heating.
Leaky or undersized ducts waste 20–30% of heated air. Duct sealing or replacement during furnace install improves comfort and efficiency.
Proper sizing via Manual J calculation ensures efficiency and comfort. An oversized furnace short-cycles, wastes energy, and wears out faster.
Adding zone dampers and multiple thermostats to control heating by area costs $1,500–$3,500 but significantly improves comfort and efficiency in multi-story homes.
Mountain region costs are rising with population growth. High altitude and variable weather can affect project timelines. Skilled trade labor is in high demand in booming markets.
A lot of homeowners hear "gas furnace" and assume there's barely any electrical work involved. In reality, modern furnaces rely heavily on electrical components for blower motors, ignition systems, control boards, condensate pumps, and thermostats. Even when the heating source is gas, the furnace still needs a properly installed dedicated circuit and clean low-voltage controls to run reliably.
The thing that surprises people most is how often furnace replacements expose existing electrical problems nearby. I've opened plenty of furnace areas where the HVAC equipment itself was being replaced, but the electrical side had extension-cord wiring, overloaded utility circuits, loose service switches, open junction boxes, or old thermostat wire spliced together five different times. The furnace replacement suddenly becomes the first time anyone has looked closely at that area in 20 years.
One pattern I see constantly is contractors reusing old electrical infrastructure because "it still works." Existing service switches, old whip connections, low-voltage wiring, or condensate pump receptacles get left in place even when the rest of the equipment is brand new. That's how homeowners end up with callbacks where the furnace is fine but some older electrical component nearby starts failing a few months later.
The other thing people underestimate is how much modern furnaces depend on proper thermostat and control wiring. Smart thermostats, variable-speed blowers, zoning systems, humidifiers, and air cleaners all add complexity to the low-voltage side. A lot of nuisance problems people blame on the furnace itself actually trace back to bad thermostat wiring, missing common wires, or accessory wiring that was never cleaned up properly during installation.
One honest boundary here: combustion analysis, venting, airflow balancing, and furnace sizing are HVAC territory, not mine. From the electrical side, I'm looking at whether the dedicated circuit, service switch, controls, thermostat wiring, and accessory power were installed cleanly and safely.
When I review quotes, I want to see whether thermostat upgrades are included, whether new low-voltage wiring is assumed or excluded, whether condensate pump power is addressed, and whether the electrical reconnect is being fully updated or simply reused. "Reconnect existing electrical" can mean very different things depending on the contractor.
If it were my house, I'd rather spend a little more upfront cleaning up the surrounding electrical and control wiring during the furnace replacement instead of bolting new equipment onto messy infrastructure that was already overdue for attention.
Budget $79–$420 for permits and inspections. Your contractor typically handles the permit process, but confirm this upfront.
Hiring a pro? Make sure they're properly licensed — see how to get licensed as a HVAC technician in Utah.
Heating efficiency matters more in cold climates. High-efficiency units (95%+ AFUE for furnaces) cost more upfront but save significantly on heating bills over time. Heat pump systems may need supplemental heating below 0°F.
This project requires a licensed professional in Salt Lake City. Attempting furnace installation without proper licensing can void insurance and create serious safety hazards.
Compare licensed, insured contractors serving Salt Lake City.
Powered by Thumbtack
The average cost to install a furnace in Salt Lake City ranges from $2,550 to $8,170, with most homeowners paying around $4,590. This estimate includes both labor ($1,840) and materials ($2,750). Costs in Salt Lake City are near the national average due to local cost of living and labor market conditions. Get multiple quotes from licensed Salt Lake City contractors to lock in the best price.
Yes, Salt Lake City typically requires a permit for furnace installation. Budget $79–$420 for permit fees and expect 1–2 weeks for approval. Your contractor typically handles the permit application. Working without a required permit can void warranties and create problems when selling your home.
Most furnace installation projects in Salt Lake City take 1–2 days to complete. The timeline depends on project scope, contractor availability in the Salt Lake City metro area, and seasonal demand. Scheduling during Salt Lake City's off-peak season (typically fall and winter) can reduce wait times and may lower costs.
If you live in a cold climate and plan to stay in your home for 5+ years, a 95–98% AFUE furnace pays for itself through fuel savings. The extra $500–$1,500 upfront typically saves $200–$500 per year. In mild climates, the savings are smaller and payback takes longer.
Furnaces typically last 15–25 years. Replace if yours is over 15 years old and needing frequent repairs, if repair costs exceed 50% of replacement cost, or if your energy bills are climbing despite maintenance. A new furnace can cut heating costs by 20–40%.